FIBREGLASS MESH

Mesh for DuROCK Exterior Insulation Finish Systems is made of alkali-resistant fibreglass. All mesh is made by a DuROCK-approved manufacturer, with DuROCK’s logo plainly visible on the 5 ounce and high-impact reinforcing mesh products.

DOWNLOAD DOCUMENTS – DATA SHEET – MSDS

EPS BOARD

Expanded Polystyrene (EPS) insulation board for DuROCK Exterior Insulation Finish Systems is made of 100% virgin polystyrene resin, aged and cut in accordance with the requirements of ASTM E2430, and compliant with ULC-S701. EPS insulation board is made by a DuROCK-approved manufacturer, and is packaged in bags with DuROCK’s logo plainly visible. Please refer to EIF System specifications for applicable thicknesses & sheet size.

DOWNLOAD DOCUMENTS – DATA SHEET – SDS

DuROCK PUCC-ROCK is non-combustible mineral wool Insulation that includes a 10 mm deep geometrically defined drainage cavity (GDDC) on the backside and an integral alkali-resistant fibreglass mesh on the front side.

PUCC-ROCK is made from ROCKWOOL CONROCK stone wool insulation compliant with CAN/ULC-S702.1 and CAN/ULC-S114, thermal resistance R 4 per inch (RSI 0.70 per 25 mm), and density 8.5 pcf (136 kg/m³).

PUCC-ROCK is available in 2, 3, 4, 5, & 6-inch (51, 76, 102, 127, & 152 mm) thicknesses.

PUCC-ROCK is a component of DuROCK PUCCS NC EIFS. Refer to system specification and details for further information.

DOWNLOAD DOCUMENTS – DATA SHEET – SDS

UNI-TRACK

DuROCK’s patented Uni-Track is a PolyVinyl Chloride (PVC) extrusion designed to be used at horizontal terminations and at horizontal joints where DuROCK Exterior Insulation Finish Systems are expected to drain. Its one-size-fits-all profile eliminates the need to stock different profiles for every insulation thickness. DuROCK Uni-Track is three inches (76 mm) high, one inch (25 mm) wide, and ten feet (3.05 m) long. It is white in colour, but can be painted with most exterior latex paints.

DOWNLOAD DOCUMENTS – DATA SHEET – MSDS

UNI-FLASH

DuROCK Uni-Flash self-flashing drainage track is a PVC extrusion designed to be used at window heads and other similar locations where DuROCK Exterior Insulation Finish Systems are expected to drain. It’s one-size-fits-all profile eliminates the need to stock different profiles for every insulation thickness. DuROCK Uni-Flash is two inches wide (50 mm), three inches high (75 mm), and ten feet (3 m) long. It is white in colour, but it can be painted with most exterior latex paints.

DOWNLOAD DOCUMENTS – DATA SHEET

PROTECTO WRAP PRIMER FREE EIFS TAPE

Primer Free Stucco/EIFS Tape is a high performance tape designed for use with Stucco and EIFS systems to seal around penetrations and at sheathing joints and window / door flanges. Primer Free Stucco/EIFS Tape can be applied to most substrates without the use of primer or mechanical fasteners. The polyester fabric top layer provides an excellent bonding surface for cementitious and synthetic stucco coatings.

DOWNLOAD DOCUMENTS – DATA SHEET – MSDS

PUCCS Pre-Wrapped Starter Strips

PUCCS Pre-Wrapped Starter Strips are intended for use at the lower extremities of the PUCC System to facilitate drainage. Drainage locations include, but are not limited to, window heads, expansion joints, termination at grade, and termination above roofs, balconies, decks, other claddings, and soffits.

DOWNLOAD DOCUMENTS – DATA SHEET